Carbonyl compounds and furan derivatives with toxic potential evaluated in the brewing stages of craft beer.

Carbonyl compounds and furan derivatives may form adducts with DNA and cause oxidative stress to human cells, which establishes the carcinogenic potential of these compounds. The occurrence of these compounds may vary according to the processing characteristics of the beer. The objective of this study was, for the first time, to investigate the free forms of target carbonyl compounds [acetaldehyde, acrolein, ethyl carbamate (EC) and formaldehyde] and furan derivatives [furfural and furfuryl alcohol (FA)] during the brewing stages of ale and lager craft beers. Samples were evaluated using headspace-solid phase microextraction and gas chromatography with mass spectrometric detection in selected ion monitoring mode (HS-SPME-GC/MS-SIM). Acetaldehyde, acrolein, formaldehyde and furfuryl alcohol were found in all brewing stages of both beer types, while EC and furfural concentrations were below the LOD and LOQ of the method (0.1 and 0.01 µg L-1, respectively). Boiling and fermentation of ale brewing seem to be important steps for the formation of acrolein and acetaldehyde, respectively, while boiling resulted in an increase of FA in both types of beer. Conversely, pasteurisation and maturation reduced the levels of these compounds in both types of beer. An increase in concentration of acrolein has not been verified in lager brew probably due to the difference in boiling time between these two types of beer (60 and 90 min for ale and lager, respectively).

Validation of an analytical method using HS-SPME-GC/MS-SIM to assess the exposure risk to carbonyl compounds and furan derivatives through beer consumption.

Compounds with toxic potential may occur in beer, such as carbonyl compounds (acetaldehyde, acrolein, ethyl carbamate [EC] and formaldehyde) and furan derivatives [furfural and furfuryl alcohol (FA)]. The objective of this study was, for the first time, to validate a method based on headspace-solid phase microextraction using a PDMS-overcoated fibre and gas chromatography with mass spectrometric detection in selected ion monitoring mode (HS-SPME-GC/MS-SIM) to investigate target carbonyl compounds and furan derivatives in beers. Analytical curves showed proper linearity with r2 ranging from 0.9731 to 0.9960 for acetaldehyde and EC, respectively. The lowest LOD was found for acetaldehyde (0.03 µg L-1), while the lowest LOQ value (1.0 µg L-1) was found for acetaldehyde and EC, formaldehyde and furfural. Recovery (90% to 105%), intermediate precision and repeatability (lower than 13%), limits of detection and quantification (values below 2.5 µg L-1) showed that the method is suitable to simultaneously quantify these compounds. EC was detected in only two samples (1 lager and 1 ale). Furfural was found in 37% and 82% of ale and lager beers, respectively. Acetaldehyde, acrolein, formaldehyde and FA were detected in all samples. However, acrolein was the only compound found in the commercial samples at a concentration capable of causing health risk. Besides furfural and FA, four other furan-containing compounds (5-methyl-2-furan methanethiol, acetylfuran, 5-methylfurfural and γ-nonalactone) were also found in beers, however, at levels low enough not to impose potential health risk.

Matrix-compatible solid phase microextraction coating improves quantitative analysis of volatile profile throughout brewing stages.

Ethanol is the major matrix constituent of beer and has been reported as an important interfering volatile during headspace solid phase microextraction (HS-SPME) of minor compounds due to its displacement effect. The addition of a thin hydrophobic polydimethylsiloxane (PDMS) layer on a commercial divinylbenzene/Carboxen/PDMS (DVB/Car/PDMS) fiber was evaluated, for the first time, to minimize the displacement effect caused by ethanol in the quantitative determination of volatile profile of five stages of brewing. Analysis were performed through gas chromatography coupled to mass spectrometry detector. The extractive capacity of the PDMS-overcoated fiber was superior to the commercial analogous fiber, since the modified version extracted a greater number of compounds (61 versus 45) and allowed to obtain 20% more of total chromatographic area than the commercial fiber. The ethanol content of model solutions (0, 4, 8 and 12%) did not result in significant differences in responses neither to polar nor to medium polar or nonpolar analytes when PDMS-overcoated fiber was used. On the other hand, a displacement effect was observed when polar compounds were extracted by the commercial fiber. There was no need to prepare different analytical curves with distinct ethanol levels close to those found in each brewing stage, when PDMS-overcoated fiber was used. This approach turns the analytical method simpler, less laborious and time consuming. It showed adequate linearity, sensitivity, repeatability and intermediate precision. A heat map displayed the quantitative differences in the volatile profile of each stage of brewing. Mashing stood out in relation to the others steps by the highest levels of higher alcohols. Boiling was characterized by the highest levels of Maillard reaction products, while fermentation, maturation and pasteurization were discriminated by a major presence of esters. Terpenes were incorporated to the wort during boiling or fermentation and the concentration of these compounds remained similar throughout the subsequent brewing steps.